SIKORA AG: Tension Measurement Faster Than Ever Before - Wire & Cable India
Wire & Cable India
Technical Articles

SIKORA AG: Tension Measurement Faster Than Ever Before

SIKORA has developed an advanced stand-alone gauge head for quality control of optical fibers with a measuring rate of up to 10 khz that measures the tension quickly and precisely.

Introduction

The fast, lossless transfer of data over long distances via optical fiber cables is essential for our increasingly digital and connected society. The future demand for optical fiber cables is further growing due to the global establishment and expansion of 5G wireless standards, increasing intra-data traffic within data centers as well as data traffic between different data centers. Only through the establishment of an infrastructure with a wide-ranging fiber optic network can it be possible to realize the vision of autonomous driving, monitoring of important functions of IoT medical equipment or smart cities with automatic traffic management functions. They enable an extreme high bandwidth and a constantly increasing intra-data traffic – permanent and in real-time. In order to ensure an optimal quality of the optical fiber, a variety of measuring and control technologies are already applied in the drawing process at different production stages. Tension has an important impact on the optical fiber quality which influences the uncoated fiber. SIKORA AG has developed a stand-alone gauge head with a measuring rate of up to 10 kHz that measures the tension quickly and highly precisely. Therefore, it is particularly intended for optical fibers which are further processed to premium optical fiber cables and for which specific requirements and standards exist. A gauge head with such a high measuring rate is especially suitable for fast control circuits.

Tech talk 1
Measuring principle based on the birefringence principle: The tension is being determined by the change in polarization of the light entering the optical fiber relative to the double refracted emitting light that hits the receiving unit.
Requirements for the manufacturing of optical fibers and optical fiber cables

In the course of rapidly growing worldwide networking, requirements on single-mode as well as multi-mode optical fibers with regard to their relevant parameters are ever increasing. Consequently, the tolerances for attenuation, loss and cut-off frequency as well as geometrical dimensions are continually getting tighter. The optical fiber manufacturers have to take the corresponding optical fiber specifications for the target application into account. Only then, they receive exact products that effectively fulfill the guaranteed durability. Therefore, a continuous online quality control during the entire drawing process is crucial.

During the different production stages, gauge heads and processor systems measure, monitor and control the entire drawing process to ensure the quality of the optical fiber and to increase the efficiency of the production process. The objective of optical fiber manufacturers is to control as many variables as possible in the drawing process to produce a fiber with a grade of high specifications as well as minimum scrap production.

Tech talk 2
The stand-alone gauge head measures the tension of optical fibers in the drawing tower.

For example, the diameter of the fiber is controlled over the line speed. When controlling one parameter, the thus influenced factors must also be monitored because all parameters in the drawing process are linked together. Hence, as the preform temperature increases, the viscosity of the optical fiber decreases.

When line speed and tension stay the same, consequently, the diameter decreases and scrap is produced or the fiber can even break. Therefore, for higher production line speeds at consistent tension, the preform temperature is being increased. On one hand, the tension must be controlled to prevent fiber breakage. On the other hand, the controlled tension guarantees that important parameters of the produced fiber as, for example, the cut-off frequency of the attenuation parameter comply with the set specifications.

Innovative tension measurement based on the birefringence principle

There are different methods for tension measurement available on the market. One of these is the traditional vibration measuring method where a gauge head is used for the measurement of the diameter as well as the vibration of the optical fiber in the drawing process and thus determines the tension. There is no distinction between natural and forced vibration of the fiber, whereby measuring inaccuracies may occur due to stronger external environmental influences. The application of such a dual measuring system is beneficial, for example, when a lack of space in the drawing tower makes the installation of multiple stand-alone gauge heads difficult.

SIKORA AG offers a new technology for a highly precise tension measurement in a stand-alone system. This is based on the birefringence principle that uses the direction-dependent refractive characteristics of glass which occur when forces act on the glass. A light source sends polarized light that travels through the optical fiber. Due to the direction-dependent refraction index, a change of the original polarization occurs. The exiting double refracted light is received by a detection unit. This determines the difference of the polarization of the received light to the original polarization of the light source. This difference is seen as the measure for the tension exerted on the optical fiber (picture 1). The self-sufficient stand-alone measuring system offers an even more resilient and precise tension measurement for the validation as well as for the faster control of this eminently important parameter. This is achieved by the innovative measuring principle and the considerable measuring rate of up to 10 kHz. The measuring area of the system is up to 400 g and the reproducibility amounts to ± 0.1 g.

Tech talk 3
In addition to the tension, the available processor system visualizes measuring values of further SIKORA gauge heads in the drawing tower.
Use of the systems and application area

The gauge head can be either installed before or after the cold position of the uncoated fiber. The measured value is independent of production influences such as the position of the fiber in the measuring field, the production line speed as well as the vibration or oscillation of the fiber. Therefore, the gauge head can also be used for statistical offline measurements if needed. For example, the calibration of the system can be checked easily by using test probes. The system generates reliable and stable measuring values and thus enables an immediate control of the tension. The installation in existing drawing towers is possible at any time. The application of the described stand-alone gauge heads is particularly attractive for manufacturers who want to receive highest quality due to an optimal production process with minimal scrap and at smallest possible resource usage.

Visualization of the measuring data

The tension gauge head is available with all common interfaces and industrial field busses, for example, Profinet IO, EtherNet/IP or Profibus-DP. Therefore, digital or analogue data transmission is available depending on the requirements of the customer. Additionally, the gauge head can be connected to a processor system that is also available. The processor system provides further interfaces such as OPC UA and visualizes the production data. It is possible to display single measurement values, for example, for the analysis and optimization of processes. Furthermore, the measuring values of the tension gauge head can be merged with values of other measuring devices, such as diameter measurement values. Due to the combined evaluation, the so-called sensor fusion, plausibility and significance of the recorded data are being increased and the quality of the measuring results is further improved.

Further available measuring and control technology for comprehensive quality control

In addition to the stand-alone device for tension measurement, SIKORA offers systems for the measurement of the diameter and the position of the uncoated and coated fiber, which also determine the tension via vibration measuring method. Further gauge heads measure and control in combination with a processor system the temperature of the optical fiber at the hot and the cold position of the drawing process. Gauge heads for the detection of airlines, for the measurement of the concentricity of the coating and for the detection of lumps, neckdowns and blisters on the surface of the coated fiber complement SIKORA’s portfolio for the quality control of optical fiber.

Conclusion

In order to establish a sustainable infrastructure sufficient for the needs and requirements of our ever increasing digital society, the quality of the optical fibers used and thus the optical fiber cable is crucial. The measurement and control of the tension in the drawing process has a direct and significant impact on the product quality. The stand-alone gauge head developed by SIKORA AG uses a technology which applies the birefringence principle with an impressive measuring rate of up to 10 kHz. This enables an even faster and highly precise tension measurement that is independent of outer production influences and allows for immediate control of the tension. Necessary specifications are fulfilled and the high grade of the fiber is guaranteed. Therefore, the system contributes significantly to highest and reproducible quality. Additionally, it lays the foundation for an efficient and future oriented production.

Technical article by Rebecca Zachau, Corporate Communications SIKORA AG

WordPress Ads